top of page

What goes into a 33/11 kV substation for a factory, from the incoming line to the last feeder

Writer: gradeelectricalswe
gradeelectricalswe
Oct 30
8 min read

Updated 30 October 2026. Next review 30 November 2026.


A factory 33/11 kV substation is one chain: incoming line, surge arresters, isolator, metering, 33 kV breaker, power transformer, 11 kV panel, then feeders to the plant's own transformers. MSEDCL's 2024-25 cost data puts a 5 MVA station at INR 2.08 to 2.88 crore, and where a state's notified voltage is below 33 kV, as in Maharashtra, the Electrical Inspector approves it before it is energised.


The chain, bay by bay

Power crosses a 33/11 kV substation in one direction, and every bay on the way switches it, measures it or protects against a fault. The order below is the usual one on a single-line diagram, from the utility's line to the last feeder breaker.


Stage

Equipment

What it does

Incoming 33 kV line

Lightning arresters at the line entry

Divert surges to earth before they reach the transformer

Isolation

Isolator with earth switch (a gang-operated air break switch on outdoor yards)

Gives a visible break for work. It cannot quench an arc, so it is operated only with the breaker open

Measurement

Current and voltage transformers, and the tariff meter with its test terminal block

Feed the relays and the meter. Where the meter sits is usually fixed in the connection agreement

33 kV breaker

Vacuum or SF6 circuit breaker

Clears faults and switches the transformer

Power transformer

33/11 kV oil-filled unit with Buchholz relay, oil and winding temperature indicators, pressure relief device and tap changer

Steps the voltage down. The protective devices trip it on internal faults and overheating

Neutral earthing

Neutral earthing resistor or earthing transformer on the 11 kV side

Limits earth-fault current

11 kV switchgear

Incomer breaker, busbar and one breaker panel per feeder, each with current transformers and a meter

Splits the supply across the plant and trips each feeder on its own

Protection and control

Numerical relays for overcurrent and earth fault, differential protection on larger transformers, a lockout relay

Decide when to trip

Auxiliary supply

Battery bank with charger, and a station transformer

Let breakers trip when the AC supply fails, and run fans, lighting and the control room

Earthing and civil

Earth mat, fencing at least 1.8 m high around an outdoor yard, oil soak pit, fire-fighting

Limit touch and step voltage, and contain a leak


The fence and the earth mat are not optional extras. Regulation 51 of the CEA 2023 regulations requires an outdoor substation to be protected by fencing at least 1.8 m high (or other means that keep unauthorised people out, unless the apparatus is fully enclosed in an earthed metal covering), and regulation 50 requires the whole yard to be earthed to a mat that keeps touch and step potential within tolerable limits, with the transformer neutral connected to the earthing system by two separate connections.


Past the 11 kV panel, the plant's own 11/0.433 kV transformers take over. Those are load-centre substations, one per shop or block, and they are a different job from the receiving station described here.


Does the factory need 33 kV at all?

The state's supply code decides it, and the bands differ by state. In Maharashtra, clause 3.2 of the MERC Supply Code regulations of 2021 puts 11 kV up to 3,000 kVA of contract demand, 22 kV up to 7,500 kVA and 33 kV up to 10,000 kVA, with limits of 5,000, 10,000 and 20,000 kVA in a Metropolitan Area or on an express feeder.


Other states set their own bands, and the distribution company can serve you at a different voltage depending on how far the nearest feeding substation is. Get the voltage in writing before anything is designed.


The number that goes into the application should come from twelve months of metered maximum demand plus the load being added, at a realistic power factor. A nameplate total overstates the need, and today's bill alone understates the growth. For a Maharashtra connection, the related guide on HT versus LT connections in Maharashtra covers the voltage decision from the tariff side.


Outdoor, indoor or packaged

An outdoor air-insulated yard costs least to build and needs the most land and upkeep in dusty, coastal or chemical air. Indoor metal-clad switchgear (often called GIS at 33 kV, though the IEC standard for gas-insulated switchgear starts above 52 kV) costs more per bay and shrinks the plot. A packaged compact substation suits smaller loads. Plot size, site air and delivery time decide it.


Option

Land and cost

Fits when

Outdoor air-insulated yard

Most land. Lowest to build, most upkeep in polluted air

The plot is large and the air is clean

33 kV outdoor with 11 kV indoor

Medium land. MSEDCL's 1 x 5 MVA DPR is INR 273.66 lakh, against INR 287.68 lakh for an all-outdoor station

The 11 kV panels need a room and the 33 kV yard can stay outside

Indoor metal-clad 33 kV

Least land. Usually the highest cost per bay

The plot is tight or the air is aggressive

Packaged compact substation

Smallest footprint. One purchase order and one factory test

The load is smaller and speed matters. Check the rating limit with the maker


What a 33/11 kV substation costs

Published benchmarks are utility estimates. MSEDCL's Cost Data 2024-25 prices a new 33/11 kV substation (supply, erection, testing and commissioning) at INR 2.08 crore (tender cost) to INR 2.88 crore (DPR amount) for one 5 MVA transformer. Andhra Pradesh's APCPDCL puts a 1 x 5 MVA station with two to four 11 kV feeders at INR 1.24 to INR 1.37 crore.


MSEDCL, Cost Data 2024-25, outdoor 33/11 kV substation, INR lakh:


Configuration

DPR amount

Tender cost

1 x 5 MVA

287.68

207.70

1 x 10 MVA

356.03

256.18

2 x 5 MVA

433.05

311.00

1 x 5 MVA and 1 x 10 MVA

504.71

361.83

2 x 10 MVA

569.05

407.46

Adding a 5 MVA transformer to an existing station

145.49

103.36

Adding a 10 MVA transformer to an existing station

214.55

152.34


APCPDCL, Cost Data 2023-24, INR lakh:


Item

Cost

33/11 kV substation, 1 x 5 MVA, 2 feeders, no capacitor bank

123.68

Same, 3 feeders

128.74

Same, 4 feeders

137.06

Same, 3 feeders, with a 2 MVAR 11 kV capacitor bank

152.77

Additional 5 MVA transformer with 33 kV bay

78.51

Additional 8 MVA transformer with 33 kV bay

95.12


MSEDCL's tender column runs at 71 to 72% of its DPR column on every row. For a 5 MVA station its figures are roughly 1.5 to 2.3 times APCPDCL's, and neither document explains the gap, so read the range as an order of magnitude. Both price stations the way a utility builds them. They are not quotes for a factory-owned station, and land, the incoming 33 kV line and the factory's own 11 kV network need their own lines in any bid.


Approvals, in the order they happen

Two clearances run side by side and neither replaces the other: the distribution company's sanction of supply, and the Electrical Inspector's approval of the installation. Above the state's notified voltage, regulation 45 requires the Inspector's written approval before supply starts, and regulation 45(4) bars the supplier from commencing supply to such an installation without it.


  1. Fix the contract demand and the supply voltage, then apply to the distribution company with the land papers, the load details and the proposed single-line diagram. It studies feasibility and issues its estimate and the connection agreement.

  2. Design to what that agreement says about the point of supply, the metering and the protection interface.

  3. Build with a contractor licensed by the state, working under a certificate-of-competency holder. Regulation 31 says installation work done any other way cannot be energised or connected to the supplier's system.

  4. Run the site tests on every new circuit and apparatus above 650 V, and record the results (regulations 45(5) and 48).

  5. Apply to the Electrical Inspector for inspection and written approval, with the test records. The CEIG approval guide for Maharashtra covers that route in the state where Grade is based.

  6. The distribution company charges the line once the approval is in hand.


In a state whose notified voltage is 33 kV, as Delhi's 2017 notification set it, the owner self-certifies instead of waiting for the Inspector, and the same tests apply. The CEA 2023 guide for factories sets out the notified voltage, who signs, and what the inspector's form asks to see.


Tests before energising

Regulation 48 requires site tests on any new apparatus above 650 V before commissioning, and the Electrical Inspector can ask for the manufacturer's type, acceptance and routine test certificates. The inspector's own form lists what gets reported.


That list covers isolator and breaker contact resistance, insulation resistance, breaker timing and interlocks, transformer insulation resistance, oil breakdown voltage, vector group, polarity, magnetic balance and tan delta, current and potential transformer ratio and polarity, cable insulation resistance, and the resistance of each earth electrode and of the mat.


Commissioning adds checks the form does not itemise: secondary injection on every relay, current transformer magnetising curves, panel interlocks, a trip test of the Buchholz and temperature devices, and a stepwise energisation under a written switching programme. Keep every reading. Regulation 48(6) requires records that can be compared with past records, and next year's tests are only as useful as this year's baseline.


Who owns it and who maintains it

It depends on the state's supply code and the scheme the connection is released under. Usually the factory owns and maintains its receiving substation behind the distribution company's metering point, and regulation 32(8) makes the owner responsible for keeping it free from danger. Some states run deposit-work schemes in which the utility owns what the consumer paid for, which changes the drawings and who you call when it trips.


An owned 33 kV yard comes with a yearly obligation: oil samples, earth resistance and protection checks that the Electrical Inspector's form asks about.


Sequencing mistakes that cost time

Avoidable delay comes from doing steps in the wrong order. Fixing the supply voltage and the point of supply in writing comes first, and the four mistakes below are each cheap to avoid early and expensive to repair once the drawings are frozen.


  • Designing before the supply voltage and the point of supply are in writing, so the drawings have to be redone.

  • Sizing on today's bill, so the second transformer needs a new room, a new bay and a second approval within a few years. Leave space and a spare bay.

  • Taking the drawings to the Electrical Inspector after they are frozen, when a clearance, soak pit or fence change means rework.

  • Leaving the earth mat to the end. Regulation 50 sets what it must achieve, and the inspector's form asks for the resistance of each electrode and of the mat.


Questions factories ask

What is the maximum capacity of a 33 kV substation?

There is no single maximum. Factory receiving stations are commonly built around 5 MVA and 10 MVA transformers, the two sizes MSEDCL's cost data prices, and the utility's feeding substation limits what it can supply.


What is the difference between a 33/11 kV and an 11/0.433 kV substation?

The 33/11 kV station is the factory's receiving point. It takes the utility's 33 kV supply and creates the plant's 11 kV network. The 11/0.433 kV stations tap that network near the loads and give the 433 V (415 V at the terminals) that runs motors and lighting.


How much does a 33/11 kV transformer cost?

Neither utility sheet prices the transformer alone. MSEDCL prices an additional 5 MVA power transformer at INR 145.49 lakh (DPR) or INR 103.36 lakh (tender) and a 10 MVA one at INR 214.55 or INR 152.34 lakh, each including supply, erection, testing and commissioning.


RMU or VCB panel at the 11 kV incomer?

A VCB panel usually suits the incomer, because it interrupts the full fault current and carries adjustable protection and metering. An RMU's ring switches break load current only and rely on a fuse or breaker on the tee-off, which suits a ring node or a single-transformer kiosk. Check what your distribution company requires before choosing.


Work with Grade

Grade Electricals builds this kind of substation, which is worth keeping in mind as you read the rest. Its turnkey projects page covers LV and HV electrification up to 33 kV, from design to commissioning. Its liaisoning page lists the Electrical Inspector's office, MSEDCL, BEST, Tata Power and Adani Electricity among the authorities it deals with, and its maintenance page covers testing and upkeep of substations up to 33 kV. To discuss a project, use the contact page.

Recent Posts

See All

Comments


Head Office

Unit No.5, Y.A.Chunawala Indl.Estate, Near Jacob Building, Kondivita Road, J.B.Nagar, Andheri [E], Mumbai- 400 059

+91 22 28366241 / 42

enquiry@gradeelectricals.com

Inquiries

For any inquiries, questions or commendations, please call: +91 22 28366241 / 42

© 2025 by Grade Electricals Pvt. Ltd.

bottom of page