top of page

Which transformer tests a plant should order every year, and which ones only after a fault

Writer: gradeelectricalswe
gradeelectricalswe
Oct 30
7 min read

Updated 30 October 2026. Next review 30 November 2026.


Every year: an oil sample, insulation resistance, earth resistance, a check of the protection devices and an infrared scan under load. On a schedule set by the transformer's age and how much the plant depends on it: gas-in-oil analysis. Mostly after a fault, a repair or a doubt: tan delta, SFRA, winding resistance and turns ratio. No single Indian rule fixes the calendar, so the plant's own schedule and records are the evidence.


What the rules fix and what they leave to you

The CEA 2023 regulations require site tests on new apparatus above 650 V before it is commissioned (regulation 48(2)) and periodic tests afterwards "as per the relevant standards" (48(5)). They also require records of tests, trippings, maintenance and repairs kept so they can be compared with past records (48(6)). The standards do not fix one calendar either, which is why transformer testing frequency varies so much from plant to plant.


IS 1866:2000, the code of practice for insulating oil in service, says it is impossible to lay down a general rule for how often oil should be examined. It also leaves transformers up to 1 MVA and 36 kV out of its equipment categories because routine monitoring of such small units is considered uneconomical, and says Category C guidance is adequate where a plant wants a programme anyway.


IS 10028 (Part 3):1981 is the maintenance code, and it does give a schedule. It has one table for transformers below 1,000 kVA and one for 1,000 kVA and above, covering oil dielectric strength and water content, acidity and sludge, earth resistance, and relay and alarm checks. For the heavy work, the scanned text reads as overall inspection with lifting of the core and coils every five years for 1,000 to 3,000 kVA and every seven to ten years above 3,000 kVA. The interval for each other line is in the standard, and the manufacturer's instructions apply on top of it.


The inspector's own form, Form III of Schedule II to the CEA regulations, asks whether transformer oil samples are tested periodically with the dielectric strength recorded, whether earth resistance is measured once a year, and whether residual life assessment is under way for equipment more than 15 years old. Those three questions are the closest thing to a statutory test list for a plant transformer.


The yearly set

These are the tests a plant should expect at every annual shutdown, each tied to the rule or standard that asks for it. Together they cover the oil, the winding insulation, the earthing, the protection devices and the hot spots a thermal scan finds.


Test

What it catches

Why it is yearly

Oil sample: breakdown voltage, water content, acidity, sludge

Moisture, contamination, oil ageing

IS 10028 (Part 3) lists oil tests, and Form III asks for the dielectric strength

Insulation resistance, HT to LT, HT to earth, LT to earth

Moisture and deterioration in the winding insulation

Form III reports it for every transformer

Earth resistance of the body and neutral electrodes

Loose or corroded earthing

Form III asks for it once a year

Buchholz relay, oil and winding temperature devices, pressure relief, alarm and trip operation

Protection that no longer trips

Form III asks for their operation and settings

Infrared scan under load

Hot joints, bushing and tap-changer problems

Standard maintenance practice; needs the transformer on load, not an outage


Insulation resistance has no universal pass mark. Compare each reading with the commissioning value at the same temperature and watch the direction over the years. Suppose a winding read 5 GΩ two years ago and reads 800 MΩ today: that is a problem even if 800 MΩ clears someone's minimum.


Gas-in-oil analysis is not on a statutory annual list, since the form asks for the oil's dielectric strength and not for gases. IS 1866 leaves the frequency to the plant's judgement, and every year is a sensible default on a critical or older unit.


Why a good oil BDV proves little on an old transformer

Breakdown voltage responds to free water and particles in the oil. It does not read the gases a developing fault produces, and it does not read the condition of the paper insulation. A 15-year-old transformer can pass on BDV with its oil chemically tired and its paper weakened.


Form III asks about residual life assessment for equipment past 15 years for the same reason, and an older unit's budget is better spent on gas-in-oil analysis, moisture in the oil, and furan or degree-of-polymerisation results that speak for the paper. Keep BDV in the yearly set because it is cheap and it catches contamination. Just do not let it be the only oil result. The values for in-service oil are in Grade's guide to transformer oil BDV test values.


Reading a gas-in-oil report

A gas-in-oil (DGA) report is a trend more than a verdict, and the order you read it in changes what you conclude. Start with acetylene, move to the individual gases, compare with the previous sample, and only then ask which fault the pattern suggests.


  1. Look at acetylene first. It is the gas of arcing, and any acetylene in a sealed unit deserves a question before you read further. Trace amounts in a new unit can be weld residue, and some load-break switch designs release it, so check the history before acting.

  2. Read each gas against the lab's limits, and treat them as flags, not verdicts.

  3. Compare with the previous sample. A steady, low gas level is a different story from a level that doubled between samples.

  4. Only then ask which fault type the gas pattern points to. Duval triangle and ratio methods are the usual tools, and a good report states which one it used.


The action follows the trend. A stable report means routine sampling continues. A rising one means a repeat sample sooner, and a rising one with acetylene means bringing in someone who can judge whether to restrict load or schedule an outage.


Tan delta and SFRA, when they earn their cost

Tan delta shows how lossy the insulation has become, and SFRA shows whether the winding or core has moved. Both are comparative tests, so each is only as useful as the reference it is compared with, and both are ordered on a trigger instead of a calendar date.


Tan delta (insulation power factor, with capacitance) measures how lossy the winding and bushing insulation has become. The reading depends strongly on temperature, so it must be corrected to a standard temperature and compared with the unit's own earlier values. Order it when moisture or ageing is suspected, when DGA or insulation resistance points that way, or on a planned diagnostic cycle for important units.


Sweep frequency response analysis (SFRA) shows whether the winding or core has physically moved. Order it after a through-fault, even when the protection cleared the fault quickly, after transport or relocation, and at commissioning to capture the fingerprint everything later is compared against. A plant with no baseline can still compare phase against phase or against an identical sister unit, which is weaker but useful.


Both need dedicated instruments. Ask any contractor which instrument they use and for a sample report before you book.


Winding resistance and turns ratio

Winding resistance reads the current-carrying path: loose joints, bad tap-changer contacts, broken strands. Phases should agree after temperature correction, and the numbers should sit near the factory values. Turns ratio reads the turns and the connections: a wrong tap, a shorted turn, a reversed lead. The usual tolerance is within 0.5% of the nameplate ratio on every tap.


Neither belongs in the yearly set for a healthy unit. Order them after tap-changer work, after a repair, after a differential or Buchholz trip, and when DGA or SFRA raises a doubt.


Tests that stay with the manufacturer

Routine, type and special tests, such as the loss measurements, the impulse test and the temperature-rise test, are factory tests under IS 1180 and IS 2026. A plant does not repeat them on site. It asks for the certificates, and regulation 48(1) lets the Electrical Inspector require them before approving an installation. Paying a site contractor for a type test the unit already has on file is paying twice for the same result.


What a useful test report shows

A test report is useful when next year's can be laid beside it. That depends on what the report records, since a bare list of readings cannot be compared with anything, and on whether the instruments behind the numbers were calibrated. A good one has the following:


  • The transformer's nameplate details and the date of the test.

  • The oil and ambient temperature at the time, with the values corrected to the reference temperature.

  • The make, model and calibration certificate of each instrument, valid on the test date. Regulation 33(3) requires test equipment used for the supplier's test of a consumer's installation to be calibrated by a government-authorised or NABL-accredited laboratory at periodic intervals, and it is a fair standard to ask of any contractor.

  • Every reading in a table beside the commissioning value and the previous year's.

  • The connection configuration used, so the next test repeats it.

  • A written conclusion and a recommended action for anything outside expectation.


For oil analysis, ask whether the laboratory's accreditation covers the specific test method on the report, and check the accreditation scope, not only the certificate.


Questions plant engineers ask

What tests are required for commissioning a transformer?

Regulation 48(2) requires site tests as per the relevant standards on new apparatus above 650 V before it is commissioned. The test list in Form III gives the practical set: insulation resistance, oil breakdown voltage, vector group, polarity, magnetic balance, tan delta, operation of the protective devices and tap changer, earth resistance, and SFRA, DFRA and partial discharge where applicable.


How often should transformer oil testing be done?

IS 1866 says no general rule can be laid down, and IS 10028 (Part 3) lists oil tests in its schedule. Form III asks whether oil is tested periodically. A yearly cycle is a sensible default for plant transformers.


What is a good tan delta value?

There is no universal value. The reading depends on temperature and on the insulation system, so compare it with the unit's own factory or commissioning value, corrected to the same temperature, and ask the contractor which reference they used.


Is a good oil BDV enough to call an old transformer healthy?

No. BDV reads contamination, not gases or paper condition. On a unit past 15 years, add gas-in-oil analysis and a paper-condition test.


Work with Grade

Disclosure: Grade Electricals sells this work. Its maintenance page lists transformer testing (insulation resistance, ratio, vector group, magnetic balance, no-load and load tests), transformer oil analysis (DGA, breakdown voltage, acidity, water content), earthing measurements, protection relay injection tests and thermographic imaging, for HV equipment up to 33 kV. It does not list tan delta or SFRA, so for those, ask any contractor, Grade included, which instrument they use and for a sample report. The CEA 2023 guide for factories explains where these tests meet the inspector's form. To discuss a plant, use the contact page.

Recent Posts

See All

Comments


Head Office

Unit No.5, Y.A.Chunawala Indl.Estate, Near Jacob Building, Kondivita Road, J.B.Nagar, Andheri [E], Mumbai- 400 059

+91 22 28366241 / 42

enquiry@gradeelectricals.com

Inquiries

For any inquiries, questions or commendations, please call: +91 22 28366241 / 42

© 2025 by Grade Electricals Pvt. Ltd.

bottom of page